/**
 *
 * \file
 *
 * \brief WINC Flash Interface.
 *
 * Copyright (c) 2017-2018 Microchip Technology Inc. and its subsidiaries.
 *
 * \asf_license_start
 *
 * \page License
 *
 * Subject to your compliance with these terms, you may use Microchip
 * software and any derivatives exclusively with Microchip products.
 * It is your responsibility to comply with third party license terms applicable
 * to your use of third party software (including open source software) that
 * may accompany Microchip software.
 *
 * THIS SOFTWARE IS SUPPLIED BY MICROCHIP "AS IS". NO WARRANTIES,
 * WHETHER EXPRESS, IMPLIED OR STATUTORY, APPLY TO THIS SOFTWARE,
 * INCLUDING ANY IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY,
 * AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL MICROCHIP BE
 * LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, INCIDENTAL OR CONSEQUENTIAL
 * LOSS, DAMAGE, COST OR EXPENSE OF ANY KIND WHATSOEVER RELATED TO THE
 * SOFTWARE, HOWEVER CAUSED, EVEN IF MICROCHIP HAS BEEN ADVISED OF THE
 * POSSIBILITY OR THE DAMAGES ARE FORESEEABLE.  TO THE FULLEST EXTENT
 * ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON ALL CLAIMS IN ANY WAY
 * RELATED TO THIS SOFTWARE WILL NOT EXCEED THE AMOUNT OF FEES, IF ANY,
 * THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR THIS SOFTWARE.
 *
 * \asf_license_stop
 *
 */


#ifndef __NM_FLASH_H__
#define __NM_FLASH_H__

/*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*
INCLUDES
*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*/
#include "common/include/nm_common.h"
#include "driver/include/m2m_types.h"

#define FLASH_RETURN_OK						0
#define FLASH_SECTOR_SIZE					FLASH_SECTOR_SZ
#define FLASH_SIGNATURE						HOST_CONTROL_FLASH_SIG
#define BACKUP_SIGNATURE					0x424b5550

#define FLASH_MODE_FLAGS_CS					NBIT0
#define FLASH_MODE_FLAGS_CS_SWITCH			NBIT1
#define FLASH_MODE_FLAGS_CS_SWITCH_TARGET	NBIT2
#define FLASH_MODE_FLAGS_CS_VALIDATE_IMAGE	NBIT3
#define FLASH_MODE_FLAGS_UNCHANGED			NBIT4
#define FLASH_MODE_FLAGS_DATA_IN_BACKUP		NBIT5

/*!	Bit 0 of u8Flags parameter of @ref tpfDataAccessFn.\n
 *	Compare buffer against existing data, to avoid unnecessary operation. */
#define FLASH_FN_FLAGS_COMPARE_BEFORE		NBIT0
/*!	Bit 1 of u8Flags parameter of @ref tpfDataAccessFn.\n
 *	Fill uninitialized portion of buffer with existing data to avoid losing it in subsequent erase.
 *	Typically not set unless @ref FLASH_FN_FLAGS_ERASE is set. */
#define FLASH_FN_FLAGS_READ_SURROUNDING		NBIT1
/*!	Bit 2 of u8Flags parameter of @ref tpfDataAccessFn.\n
 *	Save buffer to a backup persistent location in case of power loss after subsequent erase.
 *	A (persistent) record of the backup status must also be kept.
 *	Typically not set unless @ref FLASH_FN_FLAGS_READ_SURROUNDING and @ref FLASH_FN_FLAGS_ERASE are both set. */
#define FLASH_FN_FLAGS_BACKUP				NBIT2
/*!	Bit 3 of u8Flags parameter of @ref tpfDataAccessFn.\n
 *	Erase existing data before writing. */
#define FLASH_FN_FLAGS_ERASE				NBIT3
/*!	Bit 4 of u8Flags parameter of @ref tpfDataAccessFn.\n
 *	Write buffer. */
#define FLASH_FN_FLAGS_WRITE				NBIT4
/*!	Bit 5 of u8Flags parameter of @ref tpfDataAccessFn.\n
 *	Compare buffer against written data, to provide verification.
 *	Typically not set unless @ref FLASH_FN_FLAGS_WRITE is set. */
#define FLASH_FN_FLAGS_COMPARE_AFTER		NBIT5
/*!	Bit 6 of u8Flags parameter of @ref tpfDataAccessFn.\n
 *	Read data to buffer. Typically this would be the only flag set, meaning read the existing data.
 *	However, if other flags are set, the read should be performed at the end. */
#define FLASH_FN_FLAGS_READ					NBIT6

/*!	Bit 0 of u8AccessOptions parameter of various function APIs.\n
 *	Request to erase existing data before writing.\n
 *	Only applies when module is providing data to the MCU application.\n
 *	If set, @ref FLASH_FN_FLAGS_ERASE will be set in subsequent call to function of type
 *	@ref tpfDataAccessFn. */
#define FLASH_ACCESS_OPTION_ERASE_FIRST			NBIT0
/*!	Bit 1 of u8AccessOptions parameter of various function APIs.\n
 *	When set with @ref FLASH_ACCESS_OPTION_ERASE_FIRST, this is a request to do
 *	read-modify-erase-write (eg if MCU application is storing received data in flash).\n
 *	Only applies when module is providing data to the MCU application.\n
 *	If set, @ref FLASH_FN_FLAGS_READ_SURROUNDING may be set in subsequent call to function of type
 *	@ref tpfDataAccessFn. */
#define FLASH_ACCESS_OPTION_KEEP_SURROUNDING	NBIT1
/*!	Bit 2 of u8AccessOptions parameter of various function APIs.\n
 *	When set with @ref FLASH_ACCESS_OPTION_ERASE_FIRST and @ref FLASH_ACCESS_OPTION_KEEP_SURROUNDING,
 *	this is a request to keep a persistent backup of modified contents during read-modify-erase-write.\n
 *	Only applies when module is providing data to the MCU application.\n
 *	If set, @ref FLASH_FN_FLAGS_BACKUP may be set in subsequent call to function of type
 *	@ref tpfDataAccessFn. */
#define FLASH_ACCESS_OPTION_USE_BACKUP			NBIT2
/*!	Bit 3 of u8AccessOptions parameter of various function APIs.\n
 *	Request to compare new data against existing data before erasing/writing, to avoid unnecessary operations.\n
 *	Applies to data transfer in either direction.\n
 *	If set, @ref FLASH_FN_FLAGS_COMPARE_BEFORE will be set in subsequent call to function of type
 *	@ref tpfDataAccessFn. */
#define FLASH_ACCESS_OPTION_COMPARE_BEFORE		NBIT3
/*!	Bit 4 of u8AccessOptions parameter of various function APIs.\n
 *	Request for byte-wise verification of write.\n
 *	Applies to data transfer in either direction.\n
 *	If set, @ref FLASH_FN_FLAGS_COMPARE_AFTER will be set in subsequent call to function of type
 *	@ref tpfDataAccessFn. */
#define FLASH_ACCESS_OPTION_COMPARE_AFTER		NBIT4
/*!	When modifying WINC flash contents, the module determines most options internally. Only two
 *	options are taken from the u8AccessOptions parameter.\n
 *	When providing data to the MCU application, the module takes all options from the
 *	u8AccessOptions parameter. */
#define FLASH_ACCESS_WINC_MASK					(FLASH_ACCESS_OPTION_COMPARE_BEFORE | FLASH_ACCESS_OPTION_COMPARE_AFTER)


typedef enum {
	CS_INITIALIZE,
	CS_INVALIDATE_RB,
	CS_VALIDATE_RB,
	CS_SWITCH,
	CS_VALIDATE_SWITCH,
	CS_GET_ACTIVE,
	CS_GET_INACTIVE,
	CS_DEINITIALIZE
}tenuCSOp;

typedef enum {
	/*
	 *	Status values arranged so that status can be updated without any erase operation.
	 */
	FLASH_STATUS_EMPTY			= 0xFFFFFFFF,
	FLASH_STATUS_NOT_ACTIVE		= 0xFFFFFF00,
	FLASH_STATUS_ACTIVE			= 0xFFFF0000,
	FLASH_STATUS_DONE			= 0xFF000000
}tenuFlashAccessStatus;

typedef enum {
	/*
	 *	Status values arranged so that status can be updated without any erase operation.
	 */
	BACKUP_STATUS_EMPTY			= 0xFFFFFFFF,
	BACKUP_STATUS_NOT_ACTIVE	= BACKUP_SIGNATURE | 0xFFFFFF00,
	BACKUP_STATUS_ACTIVE		= BACKUP_SIGNATURE,
	BACKUP_STATUS_DONE			= 0x00000000
}tenuBackupStatus;

typedef enum {
	/*
	 *	Special location ID values. If top bit is not set, the location ID is interpreted as flash address.
	 */
	MEM_ID_WINC_FLASH = 0x80000000,
	MEM_ID_WINC_ACTIVE,
	MEM_ID_WINC_INACTIVE,
	MEM_ID_NONE = 0xFFFFFFFF
}tenuMemId;

/*!
@enum	tenuFlashAccessItemMode

@brief	Transfer modes available for accessing items in WINC flash stores such as TLS root
		certificate store.
@see	m2m_flash_rootcert_access
 */
typedef enum {
	/*!	Add an item to the relevant WINC flash store. */
	FLASH_ITEM_ADD,
	/*!	Remove an item from the relevant WINC flash store. */
	FLASH_ITEM_REMOVE,
	/*!	Read an item from the relevant WINC flash store, using an identifier. */
	FLASH_ITEM_READ,
	/*!	Read an item from the relevant WINC flash store, using an index. */
	FLASH_ITEM_READIDX
}tenuFlashAccessItemMode;


typedef struct {
	uint32					u32Signature;
	tenuFlashAccessStatus	enuTransferStatus;
	uint16					u16AppId;
	uint8					u8AccessFlags;		// These correspond bitwise to application access options.
	uint8					u8ModeFlags;		// These are set internally, with reference to application mode options.
}tstrFlashAccessPersistent;
#define FLASH_SIG_SZ		(sizeof(uint32))
#define FLASH_STA_SZ		(sizeof(tenuFlashAccessStatus))
#define FLASH_SIG_STA_SZ	(FLASH_SIG_SZ+FLASH_STA_SZ)

typedef struct {
	tstrFlashAccessPersistent	strPersistentInfo;
	tpfDataAccessFn				pfDestinationFn;
	tpfDataAccessFn				pfSourceFn;
	uint32						u32Size;
}tstrFlashAccess;

typedef struct {
	tenuBackupStatus		enuTransferStatus;
	uint32					u32DestinationAddr;
	uint32					u32SourceAddr;
	uint32					u32Size;
}tstrBackup;
#define FLASH_BACKUP_STA_SZ			sizeof(tenuBackupStatus)
#define FLASH_BACKUP_STORE_SZ		(2*sizeof(tstrBackup))
#define FLASH_BACKUP_STORE_OFFSET	(HOST_CONTROL_FLASH_OFFSET + HOST_CONTROL_FLASH_SZ - FLASH_BACKUP_STORE_SZ)

/*!
@struct	\
	tstrDataAccessInitParams
@brief
	This structure contains parameters for initializing a local data access (read, erase or write).

@see	tpfDataAccessFn.
@see	FLASH_FN_FLAGS_COMPARE_BEFORE
@see	FLASH_FN_FLAGS_READ_SURROUNDING
@see	FLASH_FN_FLAGS_BACKUP
@see	FLASH_FN_FLAGS_ERASE
@see	FLASH_FN_FLAGS_WRITE
@see	FLASH_FN_FLAGS_COMPARE_AFTER
@see	FLASH_FN_FLAGS_READ
 */
typedef struct {
	/*!	Total size of data to be accessed in data location. \n
	 *	This field is set by the module in a call to @ref tpfDataAccessFn. */
	uint32	u32TotalSize;
	/*!	Flags indicating type of data access. \n
	 *	This field is set by the module in a call to @ref tpfDataAccessFn. */
	uint8	u8Flags;
	/*!	Block size, to assist with alignment. \n
	 *	This field can be set by the local memory access function @ref tpfDataAccessFn. Defaults to 0 if not set.
	 *	Recommended values are:\n
	 *	- 4096 if accessing flash memory with erase block size <= 4096.\n
	 *	- 0 if accessing normal memory. */
	uint32	u32AlignmentSize;
	/*!	Offset of access start address, relative to u32AlignmentSize. \n
	 *	This field can be set by the local memory access function @ref tpfDataAccessFn. The field is ignored if u32AlignmentSize < 2. */
	uint32	u32StartAlignment;
}tstrDataAccessInitParams;

/*!
@struct	\
	tstrDataAccessParams
@brief
	This structure contains data for local data access (read, erase or write).
@see	tpfDataAccessFn.
 */
typedef struct {
	/*!	Buffer to be written to or read from. */
	uint8	*pu8Buf;
	/*!	Total size of the buffer. */
	uint32	u32BufSize;
	/* Offset of data within the buffer. */
	uint32	u32DataOffset;
	/* Size of data to be written or read. */
	uint32	u32DataSize;
}tstrDataAccessParams;

extern uint16	gu16LastAccessId;
extern uint8	gu8Success;
extern uint8	gu8Changed;
extern uint8	gu8Init;
extern uint8	gu8Reset;

/*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*
FUNCTION PROTOTYPES
*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*/

sint8 winc_flash_write_verify(uint8 *pu8Buf, uint32 u32Offset, uint32 u32Size);
void set_internal_info(tpfDataAccessFn *ppfFn, uint32 u32LocationId);
void set_internal_info_ptr(tpfDataAccessFn *ppfFn, uint8 *pu8Ptr);
uint8 is_internal_info(tpfDataAccessFn pfFn);
sint8 recover_backup(void);
sint8 prepare_backup(uint32 u32Target);
sint8 image_get_target(uint8 *pu8Target);
sint8 rootcert_get_size(tstrRootCertEntryHeader *pstrHdr, uint16 *pu16Size);
sint8 rootcert_access(tenuFlashAccessItemMode enuMode, tstrRootCertEntryHeader *pstrReferenceHdr, uint16 *pu16EntrySize, uint8 *pu8Buff, uint32 *pu32Offset);
sint8 transfer_run(tstrFlashAccess *pstrFlashAccess);


#endif /* __NM_FLASH_H__ */