/** * * \file * * \brief WINC1500 SPI Flash. * * Copyright (c) 2017-2018 Atmel Corporation. All rights reserved. * * \asf_license_start * * \page License * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions are met: * * 1. Redistributions of source code must retain the above copyright notice, * this list of conditions and the following disclaimer. * * 2. Redistributions in binary form must reproduce the above copyright notice, * this list of conditions and the following disclaimer in the documentation * and/or other materials provided with the distribution. * * 3. The name of Atmel may not be used to endorse or promote products derived * from this software without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE * EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE * POSSIBILITY OF SUCH DAMAGE. * * \asf_license_stop * */ /** \defgroup SPIFLASH Spi Flash * @file spi_flash.h * @brief This file describe SPI flash APIs, how to use it and limitations with each one. * @section Example * This example illustrates a complete guide of how to use these APIs. * @code{.c} #include "spi_flash.h" #define DATA_TO_REPLACE "THIS IS A NEW SECTOR IN FLASH" int main() { uint8 au8FlashContent[FLASH_SECTOR_SZ] = {0}; uint32 u32FlashTotalSize = 0; uint32 u32FlashOffset = 0; ret = m2m_wifi_download_mode(); if(M2M_SUCCESS != ret) { printf("Unable to enter download mode\r\n"); } else { u32FlashTotalSize = spi_flash_get_size(); } while((u32FlashTotalSize > u32FlashOffset) && (M2M_SUCCESS == ret)) { ret = spi_flash_read(au8FlashContent, u32FlashOffset, FLASH_SECTOR_SZ); if(M2M_SUCCESS != ret) { printf("Unable to read SPI sector\r\n"); break; } memcpy(au8FlashContent, DATA_TO_REPLACE, strlen(DATA_TO_REPLACE)); ret = spi_flash_erase(u32FlashOffset, FLASH_SECTOR_SZ); if(M2M_SUCCESS != ret) { printf("Unable to erase SPI sector\r\n"); break; } ret = spi_flash_write(au8FlashContent, u32FlashOffset, FLASH_SECTOR_SZ); if(M2M_SUCCESS != ret) { printf("Unable to write SPI sector\r\n"); break; } u32FlashOffset += FLASH_SECTOR_SZ; } if(M2M_SUCCESS == ret) { printf("Successful operations\r\n"); } else { printf("Failed operations\r\n"); } while(1); return M2M_SUCCESS; } * @endcode */ #ifndef __SPI_FLASH_H__ #define __SPI_FLASH_H__ #include "common/include/nm_common.h" #include "bus_wrapper/include/nm_bus_wrapper.h" #include "driver/source/nmbus.h" #include "driver/source/nmasic.h" /** * @fn spi_flash_enable * @brief Enable spi flash operations * @version 1.0 */ sint8 spi_flash_enable(uint8 enable); /** \defgroup SPIFLASHAPI Function * @ingroup SPIFLASH */ /** @defgroup SPiFlashGetFn spi_flash_get_size * @ingroup SPIFLASHAPI */ /**@{*/ /*! * @fn uint32 spi_flash_get_size(void); * @brief Returns with \ref uint32 value which is total flash size\n * @note Returned value in Mb (Mega Bit). * @return SPI flash size in case of success and a ZERO value in case of failure. */ uint32 spi_flash_get_size(void); /**@}*/ /** @defgroup SPiFlashRead spi_flash_read * @ingroup SPIFLASHAPI */ /**@{*/ /*! * @fn sint8 spi_flash_read(uint8 *, uint32, uint32); * @brief Read a specified portion of data from SPI Flash.\n * @param [out] pu8Buf * Pointer to data buffer which will fill in with data in case of successful operation. * @param [in] u32Addr * Address (Offset) to read from at the SPI flash. * @param [in] u32Sz * Total size of data to be read in bytes * @warning * - Address (offset) plus size of data must not exceed flash size.\n * - No firmware is required for reading from SPI flash.\n * - In case of there is a running firmware, it is required to pause your firmware first * before any trial to access SPI flash to avoid any racing between host and running firmware on bus * using * @ref m2m_wifi_download_mode * @note * - It is blocking function\n * @sa m2m_wifi_download_mode, spi_flash_get_size * @return The function returns @ref M2M_SUCCESS for successful operations and a negative value otherwise. */ sint8 spi_flash_read(uint8 *pu8Buf, uint32 u32Addr, uint32 u32Sz); /**@}*/ /** @defgroup SPiFlashWrite spi_flash_write * @ingroup SPIFLASHAPI */ /**@{*/ /*! * @fn sint8 spi_flash_write(uint8 *, uint32, uint32); * @brief Write a specified portion of data to SPI Flash.\n * @param [in] pu8Buf * Pointer to data buffer which contains the required to be written. * @param [in] u32Offset * Address (Offset) to write at the SPI flash. * @param [in] u32Sz * Total number of size of data bytes * @note * - It is blocking function\n * - It is user's responsibility to verify that data has been written successfully * by reading data again and compare it with the original. * @warning * - Address (offset) plus size of data must not exceed flash size.\n * - No firmware is required for writing to SPI flash.\n * - In case of there is a running firmware, it is required to pause your firmware first * before any trial to access SPI flash to avoid any racing between host and running firmware on bus using * @ref m2m_wifi_download_mode. * - Before writing to any section, it is required to erase it first. * @sa m2m_wifi_download_mode, spi_flash_get_size, spi_flash_erase * @return The function returns @ref M2M_SUCCESS for successful operations and a negative value otherwise. */ sint8 spi_flash_write(uint8 *pu8Buf, uint32 u32Offset, uint32 u32Sz); /**@}*/ /** @defgroup SPiFlashErase spi_flash_erase * @ingroup SPIFLASHAPI */ /**@{*/ /*! * @fn sint8 spi_flash_erase(uint32, uint32); * @brief Erase a specified portion of SPI Flash.\n * @param [in] u32Offset * Address (Offset) to erase from the SPI flash. * @param [in] u32Sz * Size of SPI flash required to be erased. * @note It is blocking function \n * @warning * - Address (offset) plus size of data must not exceed flash size.\n * - No firmware is required for writing to SPI flash.\n * - In case of there is a running firmware, it is required to pause your firmware first * before any trial to access SPI flash to avoid any racing between host and running firmware on bus using * @ref m2m_wifi_download_mode * - It is blocking function\n * @sa m2m_wifi_download_mode, spi_flash_get_size * @return The function returns @ref M2M_SUCCESS for successful operations and a negative value otherwise. */ sint8 spi_flash_erase(uint32 u32Offset, uint32 u32Sz); /**@}*/ #endif //__SPI_FLASH_H__